|
RADIAN
Apr 20, 2015 12:27:52 GMT
Post by Smart Aerials on Apr 20, 2015 12:27:52 GMT
Hi all, I´m new in the forum and to Radians. I just recently purchased a servo 2 axis AV200 that came with two Radians, it was working all good till I tried to connect it to the pc, didn t want to so I tried uploadind the firmware, it got stuck after erasing and now it s stuck in bootloader mode, can t connect it to pc and it doesn t work, leds are solid. Any ideas on how to fix this?? Many thanks in advance!
|
|
|
RADIAN
Apr 20, 2015 15:14:35 GMT
Post by Smart Aerials on Apr 20, 2015 15:14:35 GMT
Does Carvec software suport 3 servos from a single Radian? Regards
|
|
|
RADIAN
Apr 27, 2015 10:15:14 GMT
Post by JohnC on Apr 27, 2015 10:15:14 GMT
Welcome to the forum : sorry for the late reply ... been travelling :-).
The two LED's mean it is in bootloader mode. It sounds like your problem is the link with the PC.
Are you confident the USB adapter is configured properly ?. You can tell if it is because the LED on it will flicker when you click 'connect to target'. If not, check you have the right COM port selected.
The G-Lock upgrade does indeed support 3 servos from a single Radian. It also has lots of other features which never made it into the Radian software (like slew acceleration control).
|
|
|
RADIAN
Apr 27, 2015 17:25:50 GMT
Post by smartaerials on Apr 27, 2015 17:25:50 GMT
Hi, No worries, thanks for the reply. I can connect the other radian to the pc with no problem, but this one is stuck in bootloader mode and does not want to conect
|
|
|
RADIAN
Apr 27, 2015 19:44:36 GMT
Post by JohnC on Apr 27, 2015 19:44:36 GMT
Well, it's a long shot but I would make sure it is in bootloader mode and then try to connect.
Do the 'shorting of the pins' trick on this module while you power it up and see if it will connect.
|
|
|
RADIAN
Apr 28, 2015 7:28:40 GMT
Post by Smart Aerials on Apr 28, 2015 7:28:40 GMT
|
|
|
RADIAN
Apr 29, 2015 6:37:11 GMT
Post by JohnC on Apr 29, 2015 6:37:11 GMT
OK Alex :
Is the module doing anything at all when you click 'connect' (ie showing the ID's as FFFF or whatever) or do you get 'No response' ?.
|
|
|
RADIAN
Apr 29, 2015 9:36:04 GMT
Post by Smart Aerilas on Apr 29, 2015 9:36:04 GMT
Hi John,
NO Responce is the message. I can see that the order is getting to the Radian module cause the orange led goes of when I click Connect to tTarget, but then I get the No responce message, no ID number..
|
|
|
RADIAN
Apr 29, 2015 10:38:04 GMT
Post by JohnC on Apr 29, 2015 10:38:04 GMT
Hi Alex,
In that case I'm afraid you are definitely not going to fix it yourself at the PC.
We offer a fixed price repair service for the Radians for $50USD. We will guarantee to fix it as long as it is not physically damaged.
Send me a PM if you want to sort it out.
John.
|
|
|
RADIAN
May 4, 2015 13:35:31 GMT
Post by smartaerials on May 4, 2015 13:35:31 GMT
Hi John, I sent you a pm last week, have you recived it? Regards
|
|
|
RADIAN
May 6, 2015 9:39:28 GMT
Post by smartaerials on May 6, 2015 9:39:28 GMT
Whenever you please boss
|
|
|
RADIAN
May 7, 2015 17:55:47 GMT
Post by JohnC on May 7, 2015 17:55:47 GMT
Oops. Sorry - I didn't get any notification email !.
I'll see to it right now.
|
|
|
RADIAN
Sept 3, 2016 5:47:34 GMT
Post by upupandaway on Sept 3, 2016 5:47:34 GMT
Hello John or whoever might see this post,
I have run into a snag with installing my HSL to the G-Lock Radian. In the G-Lock Radian User manual it states in the first basic step to load a predefined G Lock configuration for your receiver into the Signal Master Module. They can be found in CARVEC forum ....
The config files are in a glk file. When I save (or attempt to save) the glk file ( These are the default configuration files to use for new setups: GLockBrushlessDefault.glk (576 B) , GLockServoDefault.glk (576 B) ) it only shows as a 1kB file with nothing in it.
Does anyone out there have a screenshot of a config file for the Cinestar / Freefly 3 axis gimbal, I can load the config manually rather than trying to save and open a glk file..
Thank you very much....standing by. Almost forgot, I am running a Cinestar 8, a Cinestar / Freefly 3 axis gimbal.
Michael
|
|
|
RADIAN
Aug 15, 2019 13:16:52 GMT
Post by ijajiaco on Aug 15, 2019 13:16:52 GMT
|
|
|
RADIAN
Sept 19, 2019 3:28:32 GMT
Post by ucesokuz on Sept 19, 2019 3:28:32 GMT
|
|